Important Plumbing Insights for Installing a Bathtub
Important Plumbing Insights for Installing a Bathtub
Blog Article
We have found this article pertaining to How to Install a Bathtub Yourself listed below on the internet and reckoned it made good sense to discuss it with you over here.
Setting up a bathtub isn't exactly brain surgery, yet it does call for solid plumbing, carpentry, and also often, tiling skills. Changing an old bathtub with a new one is likewise a moderately tough job. If the old bathtub is easily accessible, the task can move easily; if you need to open up a wall to eliminate the old tub and place the new bathtub, the job is a lot harder. In either case, the task is within a house handyman's abilities, although you will certainly require a helper to move out the old tub and embeded in the new one. Make sure you have actually certified yourself for the work and also fit trying it. Instead of employing a specialist to take control of a halfway-completed task, it is much better to think about utilizing one before you start. Chances are you may require an expert plumber to make tube connections.
This write-up will assist you install a brand-new bath tub in your shower room if you have currently bought a brand-new bathtub as well as do not require to transform the setup of your previous water pipes.
Your tools as well as product checklist need to comprise the following:
Planning for the Installment
To start with, the sustaining frame provided with the bath needs to be fitted (if called for) according to the producer's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is important to make certain that if the faucet includes a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the taps system to prevent strain on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two faucets using 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you use all of the provided washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now be ready to be suited its last setting.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your setup, then the first thing you must do is separate the water system. After doing so, switch on the faucets to drain any type of water staying in the system. The process of removing the existing faucets can be quite bothersome due to the limited access that is typically the case.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the taps. Have a towel ready for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have been gotten rid of, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from turning throughout this process. When the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any type of old securing compound.
Prior to moving on to fit the new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Tub
Utilizing the two wood boards under its feet, position the tub in the required placement. The wood boards are practical in evenly spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four little factors.
The next goal is to make certain that the bath tub is leveled all round. This can be attained by checking the level and changing the feet on the bathtub up until the spirit level reviews degree.
To mount faucets, fit all-time low of the furthest adaptable faucet adapter to the suitable supply pipe by making a compression sign up with; after that do the very same for the other faucet.
Activate the water supply and also inspect all joints and new pipework for leakages and tighten them if essential. Fill the bathtub and additionally examine the overflow outlet and the normal outlet for leakages.
Finally, repair the bath paneling as described in the manufacturer's instruction manual. Tiling as well as sealing around the tub ought to wait till the bathtub has actually been made use of at least once as this will resolve it into its final setting.
Fitting New Taps
If the tails of the new faucets are plastic, then you will need a plastic adapter to stop damages to the thread. One end of the port fits on the plastic tail of the tap as well as the other end offers a link to the existing supply pipelines.
If you require to fit a monobloc, then you will call for decreasing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the installing hole in the bath/basin guaranteeing that the washing machines remain in area in between the faucet as well as the sink. Secure the tap in place with the maker offered backnut. Once the faucet is firmly in place, the supply pipes can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical faucet ports. The previous kind ought to be linked to the tap finishes first, tightening only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the area where the bath meets the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to split a rigid seal, triggering the water to pass through the wall between the bath and the tiling, resulting in issues with wetness as well as feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your components and installations. They are sold in tubes as well as cartridges, and also are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of drenched newspaper or soft rope. Bear in mind to constantly fill up the bathtub with water before sealing, to permit the motion experienced when the bathtub remains in use. The sealant can break relatively very early if you do not take into account this activity prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing waterproof or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you liked our part on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks for taking a few minutes to browse our content. Sharing is nice. Helping people is fun. Thank you for your time invested reading it.
Get sorted, dial now! Report this page